Pure water machine installation and instructions

Pure water machine installation and instructions
Pure water machine after installation, if by reason of travel on business for a long time dont have to do?
Only need to unplug the power from the port to store the water discharge machine, to plug the power supply.
Do ordinary power need not to need, pass water?
Dont need, because pure water machine and automatic washing machine, fully automatic work, do not need to consume.
Do water power have influence on the machine? No, also do not need to turn off the water electricity.
Nurture in the family how to fully use the pure water machine?
1, cooking, cooking is excellent.
2, whiter teeth brushing your teeth and health.
3, drinking water, delicious, sweet, quench thirst.
4, tea, coffee, milk, more delicious, taste even more pure.
5, pure water is one of the best make up water, on the face of the pollutants can be washed away, womens, childrens health and skin care often use pure water, can make skin more smooth, clean and elastic.
6, the ice crystal clear.
7, steam iron, humidification machine, no scaling, prolong service life.
8, the animals drink pure water is the best, not only to quench thirst, more will be out most of the impurities and toxins in the body.
【 】 pure water machine fault diagnosis
(a) high pressure pump is not started, cannot make water
1) check whether the power outage, if plug plug in
(2) check whether low voltage switch failure, cannot be switched on
(3) check if the pump and transformer short circuit, or the whole machine line connection is wrong (4) check whether the high voltage switch or water level controller is failure, cant reset (5) check box if there is a computer fault type (microcomputer)
(2) the high pressure pump to work properly, but cannot make water
1) high pressure pump pressure loss
(2) the water solenoid valve (valve) all defective cant feed water (pure water waste water are not)
(3) the front filter clogging (pure water waste water are no small or waste water)
(4) check valve failure (with waste water without water)
(5) automatic flush solenoid valve failure, cannot effectively closed (has been in a flush status)
6 defective computer box cannot be closed recoil solenoid valve (has been in a flush status) 7 RO membrane congestion
(3) the high pressure pump is not down (1) high pressure pump pressure is insufficient, cannot achieve high pressure set pressure
(2) check valve plug, not out of the water (3) high pressure failure, cant jump
(4) high pressure pump stop, but the waste water constantly
(1) the electromagnetic valve (valve) all around failure, cannot effectively without water
(2) computer box is faulty, electromagnetic valve type (microcomputer) cannot be shut down
(3) check valve pressure relief (wastewater flow small)
(5), after the expiration of the water machine repeatedly jump (1) lack of raw water pressure (2) check valve pressure relief
(3) (4) the system has a high voltage switch or liquid level switch failure phenomenon of pressure
Pail full pressure (6), but water cannot flow (1) pressure relief pressure barrels (inflatable until barrels in the inland waters just all out, about 3 kg pressure) (2) rear activated carbon block
(7) water flow less than 1) pre filter plug (2) lack of high-pressure pump pressure (3) RO membrane wastewater proportion is too conduction block (4) (5) the rear activated carbon block 6 insufficient pressure barrels or internal damage
"Pure water machine instructions"
1, close the tap water main switch, tap water, bags of feed water tee will part on the side of hole connected to 1/4 "ball valve, electroplating electroplating ball valve outlet 1/4" PE pipe. Of another place to take back the original directly remove the faucet and the other end to take back the original water.
2, at the counter near the faucet, drill a hole can be through the water of the PE pipe, and then by electroplating ball valve connected to PE pipe and through the drill hole, pull PE pipe to RO place inside kitchen (such as flow within the cabinet below), and water inlet connected to the host. After the hole connected pipes on silica gel in order to prevent water seepage into the counter.
3, drain plug in 1/4 "PE pipe, and the import of the counter drain (drains must drill a hole to insert PE pipe).
4, in current stage on the right place to drill a 11 mm holes, and then install gooseneck faucet, gooseneck faucet tube connected to the bottom of the tooth 1/4 "PE pipe, PE pipe joint and to rear RO machine activated carbon at the exit. If need fixed gooseneck faucet in the wall, can use stainless steel gooseneck hanging piece without drilling on the flow theory.
5, will pressure barrels to pressure ball valve and 1/4 "pipe joint and then connected to 1/4" PE pipe, the other end of the tube is connected to the RO machine corps of activated carbon inlet tee joint.
6, the front three filter fold after sealing according to the corresponding tag into the filter shell.
7, the inlet pipe of RO membrane tube will be removed in a container, open water and plugged in to three pretreatment of completely filled with water and activated carbon filter shell powder crumbs dissolve in the water flow, with black water, temporarily shut down the power supply first, then remove the RO feed line installed, the installation is complete.